LMR-600-FR-PVC Coaxial cable is and extremely popular product within the Times Microwave LMR coaxial cable range. The LMR range is recognised globally as the industry standard ultra low loss, flexible, low cost, lightweight, DC – 6GHz coaxial cable solution for many RF applications. This is also backed up by the best warranty and technical support in the business.
LMR-600-FR-PVC has a UL/NEC & CSA rating of ‘CMR’ and ‘FT4’ respectively. It is less expensive than LMR-600-FR, however it emits toxic fumes (HCL) and greater smoke density when burned.
Why choose LMR-600-FR-PVC?
LMR-600-FR-PVC excellent reliability, surpassed flexibility and ultra low attenuation. The LMR-600-FR-PVC cable has loss figures comparable to the extremely rigid corrugated coaxial cables however manages to achieve unsurpassed flexibility, making the cable much easier to install. Installing the connectors on the LMR-600-PVC cable versus corrugated copper cables in much quicker and simpler.
How is the LMR-600-FR-PVC low loss figures achieved?
This is achieved due to the cable construction specifications. The centre conductor uses a high conductivity, Bare copper clad covered aluminium centre conductor material. The dielectric is nitrogen injected, foamed, closed cell, Polyethylene which helps achieve 85% Velocity of Propagation. The Dielectric has an Aluminium foil outer conductor, which is chemically bonded on to it. Due to the cable construction, The attenuation is significantly lower as compared to single shielded coaxial cables: RF shielding of LMR-600 is > 90 db.
The LMR-600-FR-PVC cable comes with a black FRPVC outer jacket. This is somewhat more flexible than the standard LMR-600 cable. This is an outdoor/indoor general purpose, ultra low loss, coaxial cable.
Frequency Operating Band
LMR-600-FR-PVC is designed to operate excellent from DC – 6GHz. For any frequency band at VHF and above LMR is the obvious choice.
- Jumper Assemblies in Wireless Communications Systems
- Short Antenna Feeder runs
- 3G or 4G repeaters
- Radio antennas or receivers
- VSAT Applications
- VHF Radio communications
- UHF Radio communications
Attenuation dB figures per 100m
Temperature range: -40⁰C – +85⁰C
|LMR-600-FR-PVC ‘TC’ (solder-on center pin) Connectors|
|TC-600-716FC||7/16 DIN Female clamp connector|
|TC-600-716MC||7/16 DIN Male clamp connector|
|TC-600-716M-X||7/16 DIN Male crimp connector (solder-on pin) hex nut, no braid trim|
|TC-600-716M-RA-D||7/16 DIN Male crimp right angle connector|
|TC-600-HNMC||HN-Male (plug) clamp connector|
|TC-600-LCM||LC-Male (plug) clamp connector|
|TC-600-NF-X||N-Female (jack) crimp connector (solder-on-pin)|
|TC-600-NF-BH||N-Female (jack) crimp bulkhead connector|
|TC-600-NFC-BH||N-Female (jack) clamp bulkhead connector|
|TC-600-NMC-2-D||N-Male (plug) straight solder pin (2 pieces) clamp connector|
|TC-600-NMC||N-Male (plug) clamp hex coupling nut connector|
|TC-600-NMH-X||N-Male (plug) crimp connector (solder-on pin) hex/knurl nut, no braid trim for use to 8 GHz|
|TC-600-NMH-75/50||N-Male (plug) crimp connector (solder-on pin) for LMR-600-75 (50-ohm Interface)|
|TC-600-NMH-RA-D||N-Male (plug) crimp right angle connector|
|TC-600-QDSM||QDS-Male (plug) clamp connector|
|TC-600-TM-X||TNC-Male (plug) crimp connector (solder-on pin) hex/knurl nut, no braid trim|
|TC-600-TF-X||TNC-Female (jack) crimp connector hex/knurl nut, no braid trim|
|TC-600-TF-RP||TNC-Female (jack) crimp/reverse polarity (solder-on male pin)|
|TC-600-TM-RP||TNC-Male (plug) crimp/reverse polarity (solder-on female pin)|
|TC-600-TM-RA-D||TNC-Male (plug) crimp right angle connector+A1|
|TC-600-UMC||UHF-Male (plug) clamp connector|
|TC-600-4310M-X||4.3/10 mini DIN Male (plug) solder-pin, hex/nut.|
|LMR-600-FR-PVC ‘EZ’ Install (non-solder) Connectors|
|EZ-600-4310M-X||4.3/10-male (plug) crimp connector, non-solder pin, no braid trim|
|EZ-600-4310M-RA-X||4.3/10-male (plug) right angle crimp connector, non-solder pin, no braid trim|
|EZ-600-716F-X||7/16 DIN Female crimp; (non-solder pin)|
|EZ-600-716M-X||7/16 DIN Male crimp, hex coupling nut/non-solder pin/no braid trim|
|EZ-600-716M-RA-X||7/16 DIN Male crimp right angle; (non-solder pin), no braid trim|
|EZ-600-78 EIA||7/8 EIA Flange clamp connector|
|EZ-600-FM-75-X||F-male (plug) crimp connector, non-solder pin, no braid trim|
|EZ-600-NF-BH-X||N-female (jack) bulkhead, crimp connector, non-solder pin, no braid trim|
|EZ-600-NF-BH||N-Female (jack) crimp bulkhead connector/non-solder pin|
|EZ-600-NF-X||N-Female (jack) crimp connector, non-solder pin|
|EZ-600-NMH-X||N-Male (plug) crimp connector (non-solder pin) hex/knurl nut, no braid trim|
|EZ-600-NM-75||N-Male (plug) crimp connector (non-solder pin) for LMR-600-75|
|EZ-600-NMC-2-D||N-Male (plug) clamp connector/non-solder pin, 2 Piece Design|
|EZ-600-NMK||N-Male (plug) crimp knurled coupling nut/non-solder|
|EZ-600-NMH-RA-X||N-Male (plug) crimp right angle connector/non-solder pin, no braid trim|
|EZ-600-QNF-X||QN-female (jack) crimp connector, non-solder pin, no braid trim|
|EZ-600-QNM-X||QN-male (plug) crimp connector, non-solder pin, no braid trim|
|EZ-600-QNM-RA-X||QN-male (plug) right angle crimp connector, non-solder pin, no braid trim|
|EZ-600-SM-X||SMA-male (plug) crimp connector, non-solder pin, no braid trim|
|EZ-600-TF-X||TNC-Female (jack) crimp connector (non-solder pin) hex/knurl nut, no braid trim|
|EZ-600-TF-BH-X||TNC-female (jack) bulkhead, crimp connector, non-solder pin, no braid trim|
|EZ-600-TF-RP||TNC-Female (jack) crimp/reverse polarity (non-solder male pin)|
|EZ-600-TM-X||TNC-Male (plug) crimp connector (non-solder pin) hex/knurl nut, no braid trim|
|EZ-600-TM-RP||TNC-Male (plug) crimp/reverse polarity (non-solder female pin)|
|EZ-600-UM||UHF-Male (plug) crimp connector/non-solder pin|
|EZ-600-UM-X||UHF-male (plug) crimp connector, non-solder pin, no braid trim|
|EZ-600-UM-RA-X||UHF-male (plug) right angle, crimp connector, non-solder pin, no braid trim|
Installing the LMR EZ connector range is the easiest in the business. Detailed instructions come with the connector, however, to ensure you achieve the correct strip length every time, with minimum effort, we have you covered. You can use our TK-600EZ Cable assembly tool kit. The tool kit consists of a CST-600 strip tool, CT-600 crimp tool and a CCT-03 Cutting tool.