Description
LMR-600-LSZH
LMR-600-LSZH Coaxial cable is an extremely popular product within the Times Microwave LMR coaxial cable range. The LMR-600-LSZH cable is recognised globally as the industry standard ultra-low loss, fire retardant, flexible, low cost, lightweight, DC – 6GHz coaxial cable solution for many RF applications. This is also backed up by the best warranty and technical support in the business.
Why choose LMR-600-LSZH?
LMR-600-LSZH is a non-halogen (non-toxic), low smoke, fire retardant cable with excellent reliability, unsurpassed flexibility and ultra-low attenuation. The LMR-600-LSZH cable has loss figures comparable to the extremely rigid corrugated coaxial cables however it has superior flexibility with a much tighter bend radius. Installing the connectors on the LMR-600-LSZH cable versus corrugated copper cables in much quicker and simpler.
How is the LMR-600-LSZH low loss figures achieved?
This is achieved due to the cable construction specifications. The centre conductor uses a high conductivity, Bare copper clad covered aluminium centre conductor material. The dielectric is nitrogen injected, foamed, closed cell, Polyethylene which helps achieve 85% Velocity of Propagation. The Dielectric has an Aluminium foil outer conductor, which is chemically bonded on to it. Due to the cable construction, the attenuation is significantly lower as compared to single shielded coaxial cables: RF shielding of LMR-600 is > 90 db.
Outer Jacket
The LMR-600-LSZH Jacket is made from fire retardant polyethylene. The cable jacket can withstand harsh outside environments and UV rays from sunlight, as well as being fully fire retardant to allow the cable to be routed indoors safely.
Flame Meets the following certifications:
- EC-332-1-2
- IEC 332-3 CAT.C
- UL-VW1
- UL-1581
- IEE-383
- BS-4066-1
- BS-4066-3
- UL-1685
- NFPA-130
Smoke meets the following certifications:
- IEC-61034-2
- NES-711
Halogen Meets the following certifications:
- IEC-60754-1
- BS 6425-1
- IEC-60754-2
- BS 6425-2
Frequency Operating Band
LMR-600-LSZH is designed to operate excellent from DC – 6GHz. For any frequency band at VHF and above LMR is the obvious choice.
Applications
LMR-600-LSZH, Flexible Low Loss Communications Coaxial Cable is ideal for:
- Jumper Assemblies in Wireless Communications Systems
- Short Antenna Feeder runs
- WLL
- GPS
- LMR
- WLAN
- WISP
- WiMAX
- SCADA
- 3G or 4G repeaters
- Radio antennas or receivers
- VSAT Applications
- TVRO
- VHF Radio communications
- UHF Radio communications
- Indoor Applications
Connectors
| LMR-600-LSZH ‘TC’ (solder-on center pin) Connectors | ||
| TC-600-716FC | 7/16 DIN Female clamp connector | |
| TC-600-716MC | 7/16 DIN Male clamp connector | |
| TC-600-716M-X | 7/16 DIN Male crimp connector (solder-on pin) hex nut, no braid trim | |
| TC-600-716M-RA-D | 7/16 DIN Male crimp right angle connector | |
| TC-600-HNMC | HN-Male (plug) clamp connector | |
| TC-600-LCM | LC-Male (plug) clamp connector | |
| TC-600-NF-X | N-Female (jack) crimp connector (solder-on-pin) | |
| TC-600-NF-BH | N-Female (jack) crimp bulkhead connector | |
| TC-600-NFC-BH | N-Female (jack) clamp bulkhead connector | |
| TC-600-NMC-2-D | N-Male (plug) straight solder pin (2 pieces) clamp connector | |
| TC-600-NMC | N-Male (plug) clamp hex coupling nut connector | |
| TC-600-NMH-X | N-Male (plug) crimp connector (solder-on pin) hex/knurl nut, no braid trim for use to 8 GHz | |
| TC-600-NMH-75/50 | N-Male (plug) crimp connector (solder-on pin) for LMR-600-75 (50-ohm Interface) | |
| TC-600-NMH-RA-D | N-Male (plug) crimp right angle connector | |
| TC-600-QDSM | QDS-Male (plug) clamp connector | |
| TC-600-TM-X | TNC-Male (plug) crimp connector (solder-on pin) hex/knurl nut, no braid trim | |
| TC-600-TF-X | TNC-Female (jack) crimp connector hex/knurl nut, no braid trim | |
| TC-600-TF-RP | TNC-Female (jack) crimp/reverse polarity (solder-on male pin) | |
| TC-600-TM-RP | TNC-Male (plug) crimp/reverse polarity (solder-on female pin) | |
| TC-600-TM-RA-D | TNC-Male (plug) crimp right angle connector+A1 | |
| TC-600-UMC | UHF-Male (plug) clamp connector | |
| TC-600-4310M-X | 4.3/10 mini DIN Male (plug) solder-pin, hex/nut. | |
| LMR-600-LSZH ‘EZ’ Install (non-solder) Connectors | ||
| EZ-600-4310M-X | 4.3/10-male (plug) crimp connector, non-solder pin, no braid trim | |
| EZ-600-4310M-RA-X | 4.3/10-male (plug) right angle crimp connector, non-solder pin, no braid trim | |
| EZ-600-716F-X | 7/16 DIN Female crimp; (non-solder pin) | |
| EZ-600-716M-X | 7/16 DIN Male crimp, hex coupling nut/non-solder pin/no braid trim | |
| EZ-600-716M-RA-X | 7/16 DIN Male crimp right angle; (non-solder pin), no braid trim | |
| EZ-600-78 EIA | 7/8 EIA Flange clamp connector | |
| EZ-600-FM-75-X | F-male (plug) crimp connector, non-solder pin, no braid trim | |
| EZ-600-NF-BH-X | N-female (jack) bulkhead, crimp connector, non-solder pin, no braid trim | |
| EZ-600-NF-BH | N-Female (jack) crimp bulkhead connector/non-solder pin | |
| EZ-600-NF-X | N-Female (jack) crimp connector, non-solder pin | |
| EZ-600-NMH-X | N-Male (plug) crimp connector (non-solder pin) hex/knurl nut, no braid trim | |
| EZ-600-NM-75 | N-Male (plug) crimp connector (non-solder pin) for LMR-600-75 | |
| EZ-600-NMC-2-D | N-Male (plug) clamp connector/non-solder pin, 2 Piece Design | |
| EZ-600-NMK | N-Male (plug) crimp knurled coupling nut/non-solder | |
| EZ-600-NMH-RA-X | N-Male (plug) crimp right angle connector/non-solder pin, no braid trim | |
| EZ-600-QNF-X | QN-female (jack) crimp connector, non-solder pin, no braid trim | |
| EZ-600-QNM-X | QN-male (plug) crimp connector, non-solder pin, no braid trim | |
| EZ-600-QNM-RA-X | QN-male (plug) right angle crimp connector, non-solder pin, no braid trim | |
| EZ-600-SM-X | SMA-male (plug) crimp connector, non-solder pin, no braid trim | |
| EZ-600-TF-X | TNC-Female (jack) crimp connector (non-solder pin) hex/knurl nut, no braid trim | |
| EZ-600-TF-BH-X | TNC-female (jack) bulkhead, crimp connector, non-solder pin, no braid trim | |
| EZ-600-TF-RP | TNC-Female (jack) crimp/reverse polarity (non-solder male pin) | |
| EZ-600-TM-X | TNC-Male (plug) crimp connector (non-solder pin) hex/knurl nut, no braid trim | |
| EZ-600-TM-RP | TNC-Male (plug) crimp/reverse polarity (non-solder female pin) | |
| EZ-600-UM | UHF-Male (plug) crimp connector/non-solder pin | |
| EZ-600-UM-X | UHF-male (plug) crimp connector, non-solder pin, no braid trim | |
| EZ-600-UM-RA-X | UHF-male (plug) right angle, crimp connector, non-solder pin, no braid trim | |
