Contact & Support: +44 (0)1592 655428
$0.00
0
Specialist Live Chat
Coaxial Cable Calculator
Enquiry Form
Home  ›  Products  ›  Coaxial Cables  ›  Low PIM Cables  ›  TCOM  ›  TCOM-400
 

TCOM-400

$23.19 EX VAT

$7.07 per foot EX VAT
  • GBP: £17.80

TCOM-400 Coaxial cable is a a very popular product for applications where repeated flexing is taking place. The construction specifications of the cable have been designed in such a way that provides continuous reliability with continuous flexure. 

tcom-400-pur-db
Need the TCOM-400-PUR-DB?
No Problem!
Foot
SKU: TCOM-400 Category:

Description

TCOM-400 

TCOM-400 cable is a Flexible Low Loss Communications Coaxial cable, supplied in any length – manufactured by Times Microwave Systems and available from McGill Microwave  – Authorised Distributor of all Times Microwave products.

TCOM-400 Coaxial cable is a very popular product for applications where repeated flexing is taking place. The construction specifications of the cable have been designed in such a way that provides continuous reliability with continuous flexure. 

Additionally, this cable provides Low Passive Inter Modulation (155 dBc Intermodulation Distortion). This cable is therefore an excellent telecommunications cable with the added benefit of unsurpassed reliability.

How is the TCOM-400 low loss figures achieved?

This is achieved due to the cable construction specifications. The centre conductor uses a high conductivity, Bare copper clad covered aluminium centre conductor material. The dielectric is nitrogen injected, foamed, closed cell, Polyethylene which helps achieve 85% Velocity of Propagation. There is a Silver Plate Copper Strip Braid over the Dielectric which helps to achieve lower DV resistance and thus keep the insertion loss low. As there is an SPC strip braid, Aluminium Tape and TC Braid, the shielding effectiveness is excellent at >100dB!

Outer Jacket

The TCOM-400 comes with a UV resistant, PE Jacket. This helps to ensure the cable jacket can withstand harsh outside environments and UV rays from sunlight, this is designed to last for up to 20 years of outdoor service.

Frequency Operating Band

TCOM-400 is designed to operate excellent from 30 MHz – 10GHz.

 Applications

 TCOM-400 is an excellent performing cable for:
  • Wireless Base Station Interconnect
  • Low Loss UHF/Microwave Interconnect
  • Cell’s on Wheels
  • Any application where there may be repeated flexure

Attenuation dB figures per 100m

30 MHz : 2.4 dB
50 MHz : 3.1 dB
150 MHz : 5.4 dB
220 MHz : 6.5 dB
450 MHz : 9.5 dB
900 MHz : 13.6 dB
1500 MHz : 17.9 dB
2500 MHz : 19.7 dB
5800 MHz: 37.6 dB
10,000 MHz: 51.4 dB

Temperature range: -40⁰C – +85⁰C 

Inner Conductor: Solid BCCAI (2.74mm)
Dielectric: Foam PE (7.24mm)
Outer conductor: SPC Strip Braid (7.49mm)
Overall Braid: Tinned copper Braid over Aluminium Tape (8.38mm)
Jacket: Black PE (10.29mm)

Mechanical Specifications

Bend Radius: installation 25.4mm
Bend Radius: repeated 101.6mm
Bending Moment: 0.68Nm
Weight lb/ft  0.12 Kg/M
Tensile Strength  72.6 Kg
Flat Plate Crush: 0.71Kg/mm

Connectors

At McGill Microwave systems, we supply a huge range of connectors that include all the common interface modes. The connectors come in EZ style fitment, for rapid solderless assembly or the traditional TC solder style connectors:
TCOM-400    ‘TC’ (solder centre pin) Connectors
TC-400-716FC 7/16 DIN Female (jack) clamp connector
TC-400-716MC 7/16 DIN Male (plug) clamp connector
TC-400-716MC-RA 7/16 DIN Male (plug) clamp connector
TC-400-716M-RA-D 7/16 DIN Male crimp right angle; (solder pin)
TC-400-716M-X 7/16 DIN Male (plug) crimp (solder-on pin), hex nut, no braid trim
TC-400-BM-X BNC-Male (plug) crimp connector, no braid trim
TC-400-BM-75-X Type BNC-Male (plug) crimp connector (crimp pin) for LMR-400-75, no braid trim
TC-400-HNM HN-Male (plug) clamp connector
TC-400-HNM-RA HN-Male (plug) crimp right angle (solder-on pin) hex/knurl nut
TC-400-MUHF Mini-UHF (plug) crimp connector
TC-400-NF-X N-Female (jack) crimp connector (solder on pin)
TC-400-NFC-BH (A) N-Female (jack) clamp bulkhead connector
TC-400-NFC N-Female (jack) clamp connector
TC-400-NM N-Male (plug) crimp/knurled coupling nut
TC-400-NMH-X N-Male (plug) crimp (solder-on pin) hex/knurl nut, no braid trim
TC-400-NM-75 N-Male (plug) crimp connector for LMR-400-75
TC-400-NM-75/50 N-Male (plug) crimp connector for LMR-400-75 (50-ohm interface)
TC-400-NMC-2 N-Male (plug) clamp connector
TC-400-NMC-RA (A) N-Male (plug) clamp right angle connector
TC-400-NMH-RA-D N-Male (plug) right angle crimp connector, no braid trim
TC-400-NMH-RA-SS N-Male (plug) crimp right angle connector/solder-on pin; stainless steel
TC-400-NM-RP N-Male (plug) crimp connector, reverse polarity (female pin)
TC-400-QDSM QDS-Male (plug) clamp connector
TC-400-QNM-X QN-Male (plug) crimp connector, solder pin, no braid trim
TC-400-SM-X SMA-Male (plug) crimp connector; no braid trim
TC-400-SF-X SMA female (jack) crimp connector, solder pin, no braid trim
TC-400-TF-X TNC-Female (jack) crimp connector, solder pin, no braid trim
TC-400-TF-RP TNC-Female (jack) crimp/reverse polarity (solder-on male pin)
TC-400-TM-X TNC Male (plug) crimp (solder-on pin) hex/knurl nut, no braid trim
TC-400-TM-RA-D TNC Male (plug) crimp right angle connector (watertight)
TC-400-TM-RP TNC-Male (plug) crimp/reverse polarity (solder-on female pin)
TC-400-TM-RP-RA-D TNC-Male (plug) crimp/reverse polarity, right angle connector, solder pin
TC-400-4310M-X 4.3/10 mini DIN Male (plug) solder-pin, hex/nut.
LMR-400    ‘EZ’ Install (non-solder) Connectors
EZ-400-4195M-X 4.1/9.5 mini DIN Male (plug) crimp (non-solder pin), hex/knurl nut, no braid trim
EZ-400-4310M-X 4.3/10-Male (plug) crimp non-solder pin, no braid trim
EZ-400-4310M-RA-X 4.3/10-Male (plug) right angle crimp non-solder pin, no braid trim
EZ-400-716M-X 7/16 DIN Male crimp; (non-solder pin) hex nut, no braid trim
EZ-400-716M-RA-X 7/16 DIN Male crimp right angle; (non-solder pin), hex nut, no braid trim
EZ-400-BM-X BNC-Male (plug) crimp connector, non-solder pin, no braid trim
EZ-400-BM-RA-X BNC-Male (plug) crimp right angle, non-solder pin, no braid trim
EZ-400-FM-75 F-Male (plug) crimp connector (non-solder pin) for LMR-400-75; knurled
EZ-400-FMH-75 F-Male (plug) crimp connector (non-solder pin) for LMR-400-75; hex
EZ-400-NF-BH-X N-female (jack) bulkhead crimp non-solder pin, no braid trim
EZ-400-NF-X N-Female (jack) crimp connector, non-solder pin
EZ-400-NMC-2-D N-Male (plug) clamp; hex/knurl coupling nut; non-solder pin; 2-piece design
EZ-400-NMH-RA-X N-Male (plug) crimp right angle (non-solder pin) hex/knurl nut, no braid trim
EZ-400-NMH-X N-Male (plug) crimp (non-solder pin) hex/knurl nut, no braid trim
EZ-400-NMK-X N-Male (plug) crimp non-solder pin, no braid trim
EZ-400-NMH-75-X N-Male (plug) crimp non-solder pin, no braid trim
EZ-400-QNF-X QN-female (jack) crimp non-solder pin, no braid trim
EZ-400-QNM-X QN-Male (plug) crimp non-solder pin, no braid trim
EZ-400-QNM-RA-X QN-Male (plug) crimp right angle non-solder pin, no braid trim
EZ-400-SF-X SMA-female (jack) crimp connector, non-solder pin, no braid trim
EZ-400-SM-X SMA-male (plug) crimp connector, non-solder pin, no braid trim
EZ-400-SM-RA-X SMA-male (plug) right angle, crimp connector, non-solder pin, no braid trim
EZ-400-TF-X TNC-Female (jack) crimp (non-solder pin) no braid trim
EZ-400-TF-BH-X TNC-female (jack) bulkhead, crimp connector, non-solder pin, no braid trim
EZ-400-TF-RP TNC-Female (jack) crimp/reverse polarity (non-solder male pin)
EZ-400-TM-X TNC-Male (plug) crimp (non-solder pin) hex/knurl nut, no braid trim
EZ-400-TM-RA-X TNC-Male (plug) crimp right angle connector/non solder pin, no braid trim
EZ-400-TM-RP TNC-Male (plug) crimp/reverse polarity (non-solder female pin)
EZ-400-UM UHF male (plug) crimp connector/non-solder pin
EZ-400-UM-X UHF-male (plug) crimp connector, non-solder pin, no braid trim
EZ-400-UM-RA-X UHF-male (plug) right angle, crimp connector, non-solder pin, no braid trim

Specification

ApplicationOutdoor
Bending Moment ft/lb0.5
Bending moment n-m0.68
Impedance (Ohm)50
JacketPE
JacketcolorBlack
Cable Od (in)0.405
Cable Od (mm)10.29
Operating Temp (C)-0.470588235
Operating Temp (F)-0.216216216
Weight kg/m0.12
suffixNULL
woosvi_sluga:0:{}

Connectors

Installation Tools

The following Hardware and Installation tools are compatible

  • CCT-02

    CCT-02 Cutting Tool

    Part NumberCCT-02
    Stock Code3192-165

    CCT-02 Cutting Tool

    The CCT-02 cutting tool is designed to give a neat cut to any of the sizes of the below coaxial cables: The Blade is hardened, ensuring there is minimum wear over time.
    Add to Cart
  • CCT-03

    CCT-03 Cutting Tool

    Part NumberCCT-03
    Stock Code3192-267

    CCT-03 Cable Cutting Tool

    The CCT-03 tool is an efficient tool for cutting LMR, TCOM and RG cables having a diameter of LMR-600 or smaller. This tool provides a clean, square cut - leaving the the cable cut perfectly round. This cutting tool has been specially designed with a perfect spring force already built in to the tool to cut the cable. All the user needs to do is simply spin the tool, and it cuts the cable perfectly itself, every time. The Cutting tool comes with hardened blade, that allows 1000’s of cable cuts, with no degradation to the blade.
    Add to Cart
  • cst-400

    CST-400 Cable Prep Tool

    Part NumberCST-400
    Stock Code3192-004
    CST-400 Cable Prep Tool
    The CST-400 manufactured by Times Microwave Systems and is designed to Strip all variations of LMR-400 cable. This tool has 3 features: Cable cut (To centre conductor), Jacket stripper and centre conductor deburring tool. There is also an adjustment setting on the stripping tool to allow to cut for Times Microwave LMR Crimp connectors or Clamp connectors. Simply set it to the correct connector type and start stripping. The Cable Prep Tool has replaceable blades however this should not need to be done regularly as the blades have been proven to have a very long lasting life.
    Add to Cart
  • TK-600EZ

    TK-600EZ

    Part NumberTK-600EZ
    Stock Code3190-1602

    TK-600EZ Cable Assembly Tool kit

    The TK-600EZ Cable Assembly Tool Kit has been designed for LMR-600 crimp and clamp connectors. The tooling in the kit can be used with all LMR-600 cables and all LMR-600 X series connectors. The TK-600EZ tool kit consists of the following items:
    • CCT-03 Cable Cutting Tool
    • CST-600 Cable Stripping Tool
    • CT-600 Crimping Tool
    • Black Tool Bag
    CCT-03 Cutting tool
    The CCT-03 cutting tool, included in the TK-600EZ Tool Kit, is the first tool used to cut the LMR coaxial cable. This has been specially designed with a perfect spring force already built in to the tool to cut the cable. All the user needs to do is simply spin the tool, and it cuts the cable perfectly itself, every time. The CCT-03 cutting tool has a hardened blade, that allows 1000's of cable cuts, with no degradation to the blade. The CCT-03 cutting tool is designed to cut from LMR-100 - LMR-600.  
    CST-600 Cable Stripping Tool
    The CST-600 Cable Stripping Tool, included in the TK-600EZ Tool Kit, is the second tool used to strip the LMR coaxial cable . This tool has 3 features: Cable cut (To centre conductor), Jacket stripper and centre conductor deburring tool. There is also an adjustment setting on the stripping tool to allow to cut for Times Microwave LMR Crimp connectors or Clamp connectors. This avoids having to take the time to read instructions and measure. Simply set it to the correct connector type and start stripping!  
    CT-600 Crimp Tool 
    The CT-600 Crimp Tool, included in the TK-600EZ Tool Kit is the final tool used to crimp the connector on to the LMR-600 coaxial cable. The Crimp Tool has been specifically designed with ultra strong dies that never wear over time. The dies are made to a very fine tolerance, specifically designed for LMR-600 X Series connectors. The result from using the CT-600 crimp tool is the perfect crimp, every time, with no tool degradation.
    Add to Cart
  • HG-400T Hoisting Grip

    Cable Hoisting Grip HG-400T

    Part NumberHG-400T
    Stock CodeHG-400T

    Cable Hoisting Grip HG-400T

     
    Add to Cart

  • Y1719 Crimp Dies

    Part NumberY1719
    Stock Code3190-202
    .429" Hex Dies
    Add to Cart

  • Crimp Rings

    Part NumberCR-400
    Stock Code3190-830
    Crimp rings for TC/EZ-400 connectors (package of 10)
    Add to Cart

  • Replacement Blade Kit

    Part NumberRB-CST
    Stock Code3192-086
    Replacement blade kit for all CST cutting tools
    Add to Cart

  • Replacement Blade

    Part NumberRB-02
    Stock Code3192-166
    Replacement blade for cutting tool
     
    Add to Cart
  • ct-u crimp tool

    CT-U Crimp Tool

    Part NumberCT-U
    Stock Code3192-181

    CT-U Crimp Tool

    Times Microwave CT-U is a universal crimp tool. The CT-U crimp tool can take different die sizes in order to crimp different sizes of connectors. The CT-U can crimp:
    Add to Cart
  • gk-s1200tt

    GK-S1200TT GROUND KIT – LMR-1200

    Part NumberGK-1200TT
    Stock CodeGK-S400TT
    The GK-S1200TT Ground kit is manufactured by Times Microwave Systems. The Ground Kit For LMR-1200 has 1/4″ crimp lug (2holes) and is RoHS Compliant. Using the GK-S1200TT ground kit eliminates the risk of damage to your RF system by directing a lightning strike away from the shield of the LMR-1200 and routing it to ground. This ground kit is designed to be fitted to all of the following LMR-1200 Cables: This kit can be used in conjunction with the Times Protect lightning protection range.
    Add to Cart